RobotPriceChannelGalaher

Professional robot in
which implements the channel trading strategy Gallagher.

The signal generated in the breakdown of the price channel boundaries
Gallagher. Gallagher indicator channel based on the maximum and minimum of 10
days. When the price breaks above the upper boundary of the channel and the closing price Gallagher
locks above this boundary - it will be a signal to buy, if the price
pierces the lower boundary of the channel Gallagher and the closing price was fixed below
this boundary - it will be a signal to sell.

Expert correctly handles errors, and works reliably
On the market. Working capital of $ 100! It is important to choose a line of work, or
the two sides, or only to buy or sell. Also, the signal can be
invert. The expert uses
basic concepts, breakeven, trawl, stoploss and take profit, as well as on the closing
opposite signal. And an important function, the correct calculation of risk. No output function unit lot, used
the concept of risk, stop loss is required, since it is measured from the lot
relatively acceptable loss for a given risk.

Any expert who is optimized without risk,
using a fixed lot, will obviously incorrect results. Since when
steal up optimization options that will increase the balance in the initial
interval history. Then everything is simple, with a large supply balance, and working
fixed lot, will be able to pass any number of stories! but when
This running expert, a different place, on the history, it is likely
drain. Therefore, the concept of risk in the optimization and operation, be sure! In this
Risk case works 1 - is 1% of the deposit.

The expert also has built-in advanced features
optimization of sorting, that is, it is desirable to optimize the using mode
"Custom max".

Overview of parameters:

• Magic - The magic number, an arbitrary integer.


• Work Period - the period for which the expert works.


• Risk -
  risk, which is included in the market is given in percentage of the total loss of the deposit,
  Lot determined relative stoploss and allowable losses when the
  stoploss.


• LotRounding - Rounding of the lot (before decimal point).


• Deviation -
  requotes.


• Sleeps -
  Waiting for the opening, closing or modifying the position.


• Withdraw -
  Virtual withdrawals in the tester, as a percentage of the starting
  deposit (necessary when optimizing a long period, to protect from the saturation
  lots).


• StopLoss -
  Stoploss.


• TakeProfit -
  Takeprofit.


• Trailing Period - The period that runs the trawl.


• Trailing Breakeven - Level bezubytka, 0 - off.


• Trailing Start - The level of the beginning of the trawl, 0 - off.


• Trailing Stop - trawl level 0 - off trawl paragraphs, the active period of the trawl.


• TrailingStep Period - Trawl the period.


• Prohibit new series - If you want to finish the current position, and
  open the following, you need to include this switch (support
  position before disconnecting the expert).


• WorkOpenLong - Permission to open a long position.


• WorkOpenShort - Permission to open a short position.


• WorkCloseLong - Resolution on the closing of long positions.


• WorkCloseShort - Resolution on the closing of short positions.


• Inversion -
  Inverting input signal.


• SignalBar -
  Bar, from which begin to look at the (1 - the first fully
  formed bar).


• Signal Period - the period for which indicators work.


• AppliedPrice - The channel running from the specified price.

Instructions for optimization in standard mode:

it's desirable
optimize using mode - "Custom
max"Which has a function of a progressive optimization that
able to slightly increase the potential forecast. establish
time interval equal to the operating period (Work Period), This period must be less than any other in
settings. install only
opening price, to optimize speed. Set the desired
time period, if necessary, and then forward, as desired. The optimization of
Default included permission to work in the specified direction, and closing
alarm. For trawl method is selected not on the items and using the last bar
said time interval (TrailingStep
Period), (Trailing Stop= 0).

establish
default settings, set to optimize the following fields:

• StopLoss - 50/10/200


• TakeProfit - 100/10/300


• Trailing Breakeven - 10/20/50


• Trailing Start - 100/10/300


• Signal Period - M15 / / H4